What measurements matter first in Fremont?

Length, depth and weight come first. Add material stiffness, bundle construction and retrieval method so arm reach and support spacing reflect real handling conditions.

Can a forklift handle every long bundle?

No. Truck capacity alone does not establish access. Check attachment suitability, load center, turning envelope and clearance through the entire approach.

Can cantilever rack stand outdoors?

Yes, when specified for the exposure. Review moisture, drainage and finish suitability alongside the stored material’s own protection requirements before selecting an outdoor arrangement.

Can existing arms transfer to another system?

Only with confirmed compatibility. Similar dimensions do not establish matching connections or ratings; identify the manufacturer and component series before proposing any interchange.

Cantilever Rack system inside a California warehouse

Fremont, California

Cantilever Rack in Fremont, CA

Cantilever rack in Fremont gives long materials an open loading face, with arms fixed to uprights and no front columns interrupting access. Bar, pipe, tube, lumber and sheet materials need support arrangements matched to their dimensions, weight and stiffness rather than spaces intended primarily for pallets.

Warm Springs and Bayside manufacturing operations can need raw material near cutting or assembly while receiving and finished goods move elsewhere. A useful layout starts with those separate movements, then positions storage so the longest bundle can enter, turn and leave without crossing an active production station.

(415) 430-9104

Why cantilever rack suits production materials

Open fronts let operators approach long bundles without threading them between front posts. Arm reach must accommodate the load depth, while rated arm capacity must match the actual loading pattern rather than a simple average across every available position.

Support spacing matters as much as overall capacity. Flexible tube, thin sections and sheet packs may need closer supports than stiff bundles. Document material overhang and the number of supporting arms before assigning a storage location or changing bundle lengths.

We operate as a division of Warehouse Equipment & Supplies Co., supplying and installing warehouse equipment since 1997. Planning begins with your inventory and handling equipment, with component identification and site measurements informing the proposed arrangement.

Free Design Consultation

CAD layout with position counts

Delivery and installation coordination

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Local Warehouse Planning

Fremont’s I-880 and I-680 connections serve manufacturing and supplier movements around Warm Springs and Bayside. Inside production buildings, storage placement should account for incoming batches, fabrication feeds and outgoing goods. A shorter travel path is useful only when operators retain enough clearance to handle the full material length without obstructing another working area.

advanced manufacturing

automotive supply and electronics

How cantilever racking is planned

The design sequence connects material measurements to support geometry and truck access. Each decision should remain traceable to the loads your team actually handles.

Record the material envelope

List minimum and maximum lengths, bundle depths, weights and packaging. Include partial bundles because removing pieces can change load distribution and make a previously stable pack harder to handle.

Set arms and upright spacing

Choose arm reach around supported load depth, then establish support spacing from material behavior. Verify arm and upright ratings together, including concentrated loads and unequal loading between storage levels.

Choose access on one or both sides

Single-sided rows can suit perimeter locations; double-sided rows provide access from two aisles. Compare total footprint, base projections and handling routes instead of assuming either arrangement always saves space.

Check handling and installation interfaces

Measure forklift turning space with the longest load, or verify side-loader travel requirements. Identify existing components and confirm manufacturer-approved compatibility before extending a system or introducing different arms and connections.

Cantilever storage rack details to confirm

Indoor placement still requires attention to moisture, chemical exposure and product protection. Outdoor arrangements need materials and finishes selected for actual weather exposure, with environmental suitability confirmed for the complete assembly rather than inferred from appearance.

Sheet packs require particular care: their edges, flexibility and contact surfaces affect support needs. Any decking or accessories must suit the intended material and the rack manufacturer’s requirements; bare arms are not automatically appropriate for every sheet product.

Selective pallet rack is generally the clearer comparison for palletized cartons or finished goods needing individual pallet access. Separating that inventory from long-material positions can keep production supply visible without forcing incompatible load shapes into one storage method.

Metal bar and tube feeding fabrication.

Lumber bundles with defined support requirements.

Sheet materials with verified bearing surfaces.

Fremont warehouse storage Cantilever system details Pallet flow alternatives Drive-in storage options

Call (415) 430-9104

Recent Installations

Pallet rack installations from our existing project gallery.

View More Projects

Plan your Fremont cantilever rack layout

Share a floor plan, material list, bundle weights and handling-equipment details. Include photographs of existing rack labels and connections so the discussion can distinguish potential extensions from equipment that needs separate evaluation. (415) 430-9104.